RCWL-0516 Microwave Radar Sensor Switch Module Body Induction Module 4–28V 100mA

$22.5 $27.9
This mini doppler radar sen­sor mod­ule is equipped with sup­port­ing DC 4–28V wide volt­age This is a mini radar motion sen­sor mod­ule is equipped with RCWL-9196 chip based on the doppler microwave induc­tion tech­nol­o­gy. It will auto­mat­i­cal­ly comt­in­u­ous­ly out­put the high lev­el TTL signel when there is motion. 360 degree no blind angle detec­tion and max­i­mum 7m sen­sor­ing dis­tance with adjustable delay time and sen­si­tiv­i­ty. It is per­fect for DIY microwave motion sen­sor light switch, human sen­sor toys, smart secu­ri­ty devices, etc.Notice:1.The right ahead of induc­tion side should’t place any met­al to block2.The front/back side should reserve more than 1cm space3.Module and instal­la­tion car­ri­er FeaturesEquipped with RCWL-9196 chip sup­port­ing 4–28V wide volt­age input, high lev­el sig­nal out­put when detect­ing the motion with active repeat trig­ger360 degree no blind angle detec­tion with 5–7m detecit­ing dis­tance, the detec­tion not affect­ed by the sur­round­ings, bet­ter per­for­mance than the IR sen­sorSup­port night detect­ing func­tion turn on /off, adjustable repeat trig­ger time and detect­ing dis­tance by add the SMD com­po­nents to the cor­re­spond­ing pinsWork­ing Volt­age: DC 4–28V, Board Size: 35.9 X 17.3mm/1.41 X 0.68inchSpecificationsOper­at­ing Volt­age: 4–28VOper­at­ing Cur­rent: 2.8mA (typ­i­cal); 3mA (max)Detec­tion Dis­tance: 5–9mTrans­mit­ting Pow­er: 20mW (typ­i­cal); 30mW (max)Out­put Volt­age: 3.2–3.4VOut­put Volt­age Dri­ving Capac­i­ty: 100mATrig­ger Way: repeat trig­gerOut­put Con­trol Low Lev­el: 0VOut­put Con­trol High Lev­el: 3.3VOper­at­ing Tem­per­a­ture: ‑20~80 cel­siusStor­age Tem­per­a­ture: ‑40~100 cel­siusAdjustment Part Introduction:1.C‑TM   Adjust repeat trig­ger time,default trig­ger time is 2s;increasing capac­i­tor’s capac­i­ty will make repeat trig­ger time longer;and actu­al count­ing trig­ger time can oper­ate as below:   Stick capac­i­tor on C‑TM,test 9196 3‑pin fre­quen­cy F,repeat trig­ger time T=(1/f)*327682.R‑GN   Detec­tion dis­tance adjustment;connect with resis­tor and detec­tion dis­tance will become shorter;if not connect,detection dis­tance is 7m;if con­nect with 1M ohm resistor,detection dis­tance is 5m3.R‑CDS   Inter­nal VCC par­al­lel con­nect with inter­nal 1M ohm resis­tor to CDS pin (that is 196 9‑pin) by R‑CDS ‚CDS con­nects with photoresistor,you can close detec­tion func­tion at nightPin Definition:3V3:3V3 pow­er out­putGND:groundOUT:control output;when detect mov­ing objects,it will out­put high lev­elVIN:input voltage,4–28VCDS:enable con­trol chip,lower than 0.7V,OUT will out­put low lev­el all the timePackage listRCWL-0516 Microwave Radar Sen­sor Switch Mod­ule x1Wiki & External linksDoc­u­men­ta­tion
Motion

Motion